§ 6 LBauO M-V # Abstandsflächen in Mecklenburg-Vorpommern In Mecklenburg-Vorpommern the depth of the setback area is 0.4 H, at least 3. m. The governing provision is § 6 LBauO M-V. H is the wall height from ground level to the point where the wall meets the roof surface. 0.4 H · min. 3. m As of 08/2026 The dimensions ## What § 6 LBauO M-V requires | Standard factor | 0.4 H | |---|---| | Minimum depth | 3. m – für Gebäude gelten feste Meter statt eines H-Faktors: Gebäudeklasse 1 bis 3 = 3 m, Klasse 4 = 4 m, Klasse 5 = 5 m; 0,4 H greift nur im Übrigen | | Commercial and industrial zones | 0.2 H – mindestens 3 m | | Central area | no separate rule — the standard factor applies | | Roof allowance | Dachflächen unter 70° Neigung werden zu einem Drittel angerechnet, ab 70° voll. Eine Zwischenstufe bei 45° gibt es nicht. für Gebäude kaum relevant, weil die Tiefe ohnehin in festen Metern bemessen wird. | | Special rule for residential buildings | in der Staffelung nach Gebäudeklassen aufgegangen | Work it out yourself ## Calculating Abstandsflächen in Mecklenburg-Vorpommern Set eaves height, roof pitch, building depth and distance to the boundary — the required depth is calculated under § 6 LBauO M-V as you go. The roof allowance is what stands out: the same building yields different values of H across the 16 states. Under § 6 LBauO M-V 6.00 m 35 ° 10.00 m 3.00 m Ridge above eaves 3.50 m of which counted 1.17 m governing height H 7.17 m required depth 3.00 m The setback area lies entirely on the plot. 3.00 m are required, 3.00 m are kept. A symmetrical gable roof and level ground are assumed. The figure is geometric, not a statement about permissibility: a local by-law, a development plan or a building encumbrance can set different dimensions. Worked through ## Worked examples at a glance Depth = 0.4 × H, but never less than 3. m. These values apply to a wall in the standard case; commercial zones, core zones and privileged boundary structures follow the figures above and below. | Wall height H | Calculation | Depth of the setback area | |---|---|---| | 3. m | 0.4 × 3. = 1.2 m → minimum applies | 3. m | | 4.5 m | 0.4 × 4.5 = 1.8 m → minimum applies | 3. m | | 6.5 m | 0.4 × 6.5 = 2.6 m → minimum applies | 3. m | | 9. m | 0.4 × 9. = 3.6 m | 3.6 m | | 12. m | 0.4 × 12. = 4.8 m | 4.8 m | Building on the boundary ## What may stand on the boundary in Mecklenburg-Vorpommern without a setback area Garages, carports and garden sheds may stand directly on the property boundary under narrow conditions. The dimensions differ in every state. | Height | 3. m | |---|---| | Length per boundary | 9. m | | Total length along all boundaries | 15. m | | Additional conditions | mittlere Wandhöhe; Dachüberstände bis 0,50 m bleiben außer Betracht | | Habitable rooms and fireplaces | Aufenthaltsräume und Feuerstätten ausgeschlossen | In comparison ## What is different in Mecklenburg-Vorpommern Das einzige Land, das die Abstandsfläche für Gebäude gar nicht aus der Höhe rechnet, sondern nach Gebäudeklasse in festen Metern festsetzt. On the roof allowance: Dachflächen unter 70° Neigung werden zu einem Drittel angerechnet, ab 70° voll. Eine Zwischenstufe bei 45° gibt es nicht. This system is shared by 6 of the 16 states. The formula that guides usually claim applies across Germany — "over 70° in full, over 45° one third" — applies in only four. [ All 16 states compared → ](https://schwarzplan.eu/abstandsflaechen/)Limits of this information ## What this page does not answer These figures reproduce the state building code. A local by-law, a development plan or a registered building encumbrance can set different dimensions — and there is no nationwide register of such by-laws. Only the building authority's own information is binding. Also not covered: provisions in the development plan, registered building encumbrances, the duty of mutual consideration between neighbours, fire-safety distances, and whether a project is exempt from a permit. And the most common error: exempt from a permit does not mean exempt from setbacks. A carport that needs no building application must still keep the setback areas. Legal reference ## Read the original Landesbauordnung Mecklenburg-Vorpommern, § 6 LBauO M-V. Last amended: Änderung vom 26.05.2026, GVOBl. M-V S. 522, in Kraft 12.06.2026. [Landesrecht Mecklenburg-Vorpommern](https://www.landesrecht-mv.de/) (Landesrechtsportal) [ View parcel boundaries in Mecklenburg-Vorpommern → ](https://schwarzplan.eu/flurkarte/mecklenburg-vorpommern/) [ Official site plan for a building application ](https://schwarzplan.eu/lageplan-bauantrag/) Other states ## Setback areas and boundary building elsewhere - [ Baden-Württemberg 0.4 H · 2.5 m ](https://schwarzplan.eu/abstandsflaechen/baden-wuerttemberg/) - [ Bayern 0.4 H · 3. m ](https://schwarzplan.eu/abstandsflaechen/bayern/) - [ Berlin 0.4 H · 3. m ](https://schwarzplan.eu/abstandsflaechen/berlin/) - [ Brandenburg 0.4 H · 3. m ](https://schwarzplan.eu/abstandsflaechen/brandenburg/) - [ Bremen 0.4 H · 3. m ](https://schwarzplan.eu/abstandsflaechen/bremen/) - [ Hamburg 0.4 H · 2.5 m ](https://schwarzplan.eu/abstandsflaechen/hamburg/) - [ Hessen 0.4 H · 2.5 m ](https://schwarzplan.eu/abstandsflaechen/hessen/) - [ Niedersachsen 0.4 H · 3. m ](https://schwarzplan.eu/abstandsflaechen/niedersachsen/) - [ Nordrhein-Westfalen 0.4 H · 3. m ](https://schwarzplan.eu/abstandsflaechen/nordrhein-westfalen/) - [ Rheinland-Pfalz 0.4 H · 3. m ](https://schwarzplan.eu/abstandsflaechen/rheinland-pfalz/) - [ Saarland 0.4 H · 3. m ](https://schwarzplan.eu/abstandsflaechen/saarland/) - [ Sachsen 0.4 H · 3. m ](https://schwarzplan.eu/abstandsflaechen/sachsen/) - [ Sachsen-Anhalt 0.4 H · 3. m ](https://schwarzplan.eu/abstandsflaechen/sachsen-anhalt/) - [ Schleswig-Holstein 0.4 H · 3. m ](https://schwarzplan.eu/abstandsflaechen/schleswig-holstein/) - [ Thüringen 0.4 H · 3. m ](https://schwarzplan.eu/abstandsflaechen/thueringen/)